ATEX Junction Boxes: Ex e Terminals, Cable Entries and Installation

Published 15 Oct 2026

ATEX hazardous area junction boxes and electrical enclosures for Ex e terminal and cable entry installations

ATEX junction boxes provide certified electrical connection points in potentially explosive atmospheres. For an Ex e increased safety junction box, reliable operation depends on the complete assembly: enclosure, terminals, conductor arrangements, cable entries, stopping plugs and earthing provisions. A suitable enclosure alone does not make every termination arrangement compliant.

This guide focuses on the practical engineering questions behind ATEX junction box installation: which terminals are permitted, how cables should enter the enclosure, what can be changed on site and what must be inspected before energisation. It is intended for electrical engineers, E&I contractors, maintenance teams and industrial buyers specifying equipment for hazardous areas.

Thorne & Derrick supply ATEX terminal and junction boxes for hazardous-area electrical installations.


Quick Answer: What Matters Most When Installing an Ex e Junction Box?

Confirm the complete assembly is suitable for the zone, Equipment Protection Level (EPL), gas or dust group, temperature limits and ambient conditions. Check that terminals and circuit loading are permitted, that certified cable glands and stopping devices preserve the protection concept, and that the required earthing and sealing arrangements remain intact.

Complete the specified inspection before energising the circuit.

ATEX Junction Box Installation: Quick Summary

Protection Concept Ex e increased safety, Ex d flameproof or other protection concepts according to the certified assembly.
Terminal Requirements Approved terminal types, conductor sizes, electrical loading, clearances and permitted terminal population.
Cable Entries Compatible certified cable glands, suitable entry threads, sealing arrangements and stopping plugs.
Installation Risks Incorrect terminals, excessive loading, compromised seals, poor earthing and unauthorised modifications.
Essential Checks Verify equipment certification, complete the specified installation checks and conduct the required initial inspection.

What Does an ATEX Junction Box Do?

An ATEX junction box accommodates electrical connections within equipment assessed for use in potentially explosive atmospheres. Depending on the certified assembly, it may connect instrumentation circuits, lighting feeds, control wiring or other permitted electrical circuits.

Hazardous-area requirements apply to the completed equipment, not simply its enclosure shell. A component-certified empty enclosure may need further assessment once terminals, cable entries and other components are installed. The final marking and documentation determine what can be used and where.

Where Are ATEX Junction Boxes Used?

  • Chemical and petrochemical processing installations.
  • Oil and gas production, storage and handling facilities.
  • Pharmaceutical and other process manufacturing sites.
  • Industrial installations with classified gas or dust hazardous areas.
  • Certified lighting, control and instrumentation systems.

For equipment selection and available configurations, see hazardous-area terminal and junction boxes.


Ex e Increased Safety: How Does It Work?

Ex e increased safety uses construction and electrical measures intended to prevent excessive temperatures and ignition-capable arcs or sparks. Its terminal assemblies are designed for the applicable requirements and must operate within defined electrical and thermal limits.

The designation may appear as Ex eb or Ex ec, with different protection levels. A box should never be selected simply because its marketing description includes “explosion proof”. The full Ex marking, including EPL and temperature limits, matters.

Ex e vs Ex d: Two Different Protection Principles

Ex e vs Ex d Junction Boxes

Consideration Ex e – Increased Safety Ex d – Flameproof
How Protection Works Uses enhanced design to reduce the possibility of ignition. Contains an internal explosion and restricts flame transmission.
Typical Installation Concern Terminal integrity, temperature rise, clearances and correct entries. Flamepath integrity, enclosure closure and certified entries.
Changes to Equipment Additional terminals or holes require verification against the approved assembly. Changes can compromise certified flameproof construction and must be controlled.
IMPORTANT: The generic term explosion proof junction box does not establish whether a product uses Ex d, Ex e or another protection concept. Specify equipment by its complete marking and certified design, not a broad search term.

Selecting and Connecting Ex e Terminals

Ex e terminals are not interchangeable solely because two products have the same apparent size or fit the same mounting rail. The completed equipment must permit the terminal type, conductor arrangement and operating conditions.

Check the Complete Electrical Arrangement

Ex e Terminal Selection and Installation Checks

Check Why It Matters What to Verify
Conductor Size and Type An unsuitable connection can loosen or overheat. Permitted conductor materials, cross-sections and number per terminal.
Current and Voltage Electrical loading contributes to temperature rise. Individual circuit ratings and overall assembly restrictions.
Terminal Quantity Adding circuits changes internal heat dissipation. Approved population, layout and power dissipation limits.
Clearances Spacing affects dielectric withstand and insulation integrity. Required clearance and creepage distances in the assembly.
Connection Method Incorrect stripping or tightening can cause poor contact. Approved ferrules, stripping length and terminal instructions.

Clearance is the shortest distance through air between conductive parts; creepage distance is measured along an insulating surface. Both can be affected by wiring position, added bridges or unsuitable accessories.

Why Spare Space Is Not Spare Capacity

An enclosure may physically accept another row of terminals but still be at its certified thermal or wiring limit. Before adding circuits, consult the permitted arrangement drawings and applicable loading instructions.

ENGINEERING TAKEAWAY: TERMINAL POPULATIONNever estimate Ex e terminal capacity from enclosure dimensions alone. The number of terminals, conductor cross-sections, connected current and permitted heat dissipation must comply with the completed assembly’s documentation.


Cable Glands, Entries and Stopping Plugs

ATEX cable glands form part of the cable entry arrangement. They must be selected for the certified protection concept and compatible with the cable, enclosure thread and environmental conditions.

What to Check Before Selecting a Gland

  • Protection concept and EPL: Suitability for the completed assembly and hazardous-area location.
  • Cable construction: Armoured, unarmoured or screened cable, including applicable bonding requirements.
  • Diameter and seal range: Compatibility with the actual cable dimensions.
  • Thread specification: Correct size, form, engagement and any required sealing accessories.
  • Environmental conditions: Ambient temperature, corrosion exposure and ingress protection.
  • Assembly instructions: Any particular limitations on the entry device or mounting arrangement.

Unused Entries Must Be Properly Closed

Unused entry holes need suitable certified stopping plugs or blanking elements installed as required by the enclosure and entry-device instructions. A standard industrial plug is not automatically suitable even if it has the correct thread.

Does IP66 Mean It Is ATEX Compliant?

No. IP66 describes protection against dust ingress and powerful water jets under specified conditions. It does not establish explosion protection suitability. The correct seals, glands and covers must also maintain the required IP protection in the completed installation.

Need a Certified Junction Box Configuration?

Explore ATEX terminal and junction boxes for installations with specific cable entry and termination requirements.

VIEW ATEX JUNCTION BOXES


Earthing, Bonding and Enclosure Materials

Metallic enclosures, gland plates, cable armour and associated conductive components may require protective earthing or bonding under the installation design. Connections must remain reliable and comply with the applicable electrical and equipment-specific requirements.

Metal Enclosures

For stainless steel and aluminium junction boxes, assess protective earth terminals, continuity between conductive parts and any specified bonding of removable components or gland plates.

GRP Enclosures

GRP junction boxes offer corrosion resistance, but their non-metallic walls do not provide an electrical continuity path between metallic cable glands. Separate bonding arrangements may therefore be required for armour, screens and other conductive components. Follow any electrostatic precautions specified for the enclosure.

Enclosure material affects environmental suitability but does not replace the need to confirm the full hazardous-area marking.


Can You Modify a Certified ATEX Junction Box?

Adding terminals, drilling cable entry holes or replacing components can alter temperature behaviour, electrical spacing, mechanical integrity or sealing. These changes must not be treated as routine workshop alterations.

Additional Terminals

Only add or substitute terminals when the proposed type, arrangement and connected loading are permitted by the certified assembly documentation, or the change has been appropriately assessed.

Additional Entry Holes

Some assemblies allow restricted entry configurations or manufacturer-authorised machining; others do not permit site modification. Check the certified drawings and manufacturer’s instructions before work begins.

Replacement Parts

Gaskets, covers, terminals, cable glands and accessories should be replaced using suitable components consistent with the certified design. Physical fit is not evidence of equivalent performance.

DO NOT ASSUME APPROVAL: If a proposed modification is not permitted or clearly covered by the equipment documentation, obtain an appropriately assessed solution before altering the assembly.

ATEX Junction Box Installation Checks

A structured review reduces the risk of missing a connection, entry-device or enclosure defect. These points are general engineering checks, not a substitute for the specified hazardous-area initial inspection or competent personnel.

Before Installation

  • Confirm the zone, EPL, gas or dust group and temperature requirements.
  • Review certification marking, instructions and any special conditions for use.
  • Check the approved terminal population, conductor sizes and circuit loading.
  • Confirm gland and stopping plug suitability for the cable and protection concept.
  • Inspect the enclosure, sealing surfaces and delivered configuration for damage.

During Installation

  • Use competent personnel and the relevant safe isolation and permit arrangements.
  • Mount the enclosure with suitable supports and access for inspection.
  • Install entries and terminate conductors by the specified methods.
  • Maintain conductor routing, insulation clearances and appropriate cable support.
  • Complete required earthing and bonding, and protect sealing surfaces.

Before Energisation

  • Inspect the completed terminal and cable entry configuration.
  • Check cover closure, gaskets, fasteners and unused entry closures.
  • Confirm electrical continuity and other specified tests have been completed.
  • Carry out the applicable initial hazardous-area inspection.
  • Record inspection findings and resolve defects before putting equipment into service.

Common Installation Defects and Consequences

ATEX Junction Box Installation: Common Defects

Defect Potential Consequence Preventative Check
Wrong Terminal Type Unassessed electrical or thermal performance. Confirm permitted component and configuration.
Excessive Circuit Loading Temperature rise beyond assembly limits. Review rating and loading documentation.
Incorrect Gland or Plug Compromised entry protection. Verify certification and cable compatibility.
Damaged Seals Loss of environmental protection. Inspect covers, gaskets and sealing surfaces.
Poor Conductor Termination High resistance or unreliable contact. Follow specified preparation and termination methods.
Missing Bonding Loss of required electrical continuity. Check earth paths and approved bonding arrangements.
Unapproved Drilling Compromised assembly conformity. Check permitted modification scope in advance.

The exact consequence depends on the assembly and its operating environment. A visible defect may indicate a more extensive installation problem, so checks should not be limited to appearance alone.


Standards, Markings and Zone Suitability

The relevant framework includes ATEX equipment requirements and the IEC 60079 series. The applicable national rules, adopted standard editions and certificate conditions must be established for the installation.

ATEX Junction Box Standards and Certification

Framework or Standard Why It Matters
ATEX 2014/34/EU Equipment and protective system conformity within the directive’s scope.
IEC 60079-0 General explosion-protected equipment requirements.
IEC 60079-7 Increased safety protection concepts including Ex eb and Ex ec.
IEC 60079-14 Selection, installation and initial inspection of electrical equipment in explosive atmospheres.
IEC 60079-17 Inspection and maintenance of electrical installations in explosive atmospheres.
IECEx International conformity assessment scheme for equipment used in explosive atmospheres.

Can an Ex e Junction Box Be Used in Zone 1?

Only when the complete equipment marking demonstrates suitability for the intended installation. For gas hazardous areas, an appropriately marked EPL Gb assembly can generally be selected for Zone 1, subject to its gas group, temperature classification, ambient limits and any specific conditions.

Equipment suitability for dust atmospheres requires the relevant dust protection marking. A gas-rated assembly should not automatically be assumed suitable for a dust zone.


Engineering Specification Checklist

For an accurate quotation and technically suitable configuration, prepare the following information before selecting the equipment:

ATEX Junction Box Specification Requirements

Hazardous Area Zone, required EPL, gas or dust group and temperature limits.
Environment Ambient temperature, exposure and required IP rating.
Electrical Circuits Voltage, current, number and function of connections.
Terminations Conductor materials, sizes and permitted terminal arrangement.
Cable Entries Cable type, diameter, gland requirements, thread sizes and quantity.
Enclosure Preferred material, dimensions, mounting and accessibility.
Compliance Applicable certifications, approvals and equipment documentation.

ATEX Junction Box Installation – Frequently Asked Questions

Q: What is an Ex e junction box?

A: An Ex e junction box is an assembly using increased safety measures such as suitable terminal construction, insulation, electrical clearances and temperature control. The completed equipment must comply with its certification and intended hazardous-area conditions.

Q: Can Ex e junction boxes be used in Zone 1?

A: Yes, if the complete equipment is appropriately marked for the required protection level and other applicable conditions, including gas group and temperature limits. Check the actual certificate and installation location.

Q: Can I add more terminals to an ATEX junction box?

A: Only where the approved assembly permits the additional terminal types, number, arrangement and electrical loading. Unused physical space alone does not prove there is additional certified capacity.

Q: Are ordinary cable glands suitable for Ex e junction boxes?

A: Not automatically. Entry devices must satisfy the enclosure protection concept and installation requirements, including cable compatibility, sealing and any relevant certification conditions.

Q: Can unused entries be closed with standard blanking plugs?

A: Use suitable stopping or blanking devices permitted for the certified entry arrangement. A standard plug is not sufficient merely because its thread fits the opening.

Q: Can holes be drilled into a certified enclosure?

A: Only where the equipment’s approved design and instructions permit the proposed modification, or an appropriate reassessment has been completed. Unauthorised drilling may compromise conformity.

Q: Is an IP66 junction box automatically ATEX compliant?

A: No. IP66 relates to protection against dust and water ingress under defined conditions. Explosion protection requires the correct equipment assessment, marking and certified assembly.

Q: Who should inspect an ATEX junction box before energisation?

A: Competent personnel with knowledge and experience appropriate to hazardous-area electrical installations must conduct the required initial inspection and record any defects before the equipment enters service.


ATEX Junction Boxes and Technical Support from Thorne & Derrick

Thorne & Derrick supply specialist ATEX and IECEx hazardous-area electrical equipment, including junction boxes, terminal enclosures and related accessories, for industrial operators, contractors and engineering teams.

Where the installation calls for particular terminal, entry or enclosure requirements, our technical sales team can help review the product specification and identify an appropriate equipment range.

Explore Relevant Hazardous-Area Equipment

Related ATEX Junction Boxes and Electrical Enclosures

Product Range Application Explore
ATEX Terminal & Junction Boxes Electrical connections and terminations in classified areas. View Range
Hazardous Area Enclosures Electrical enclosure selection by environment and certification. View Range
Ex e Aluminium Terminal Boxes Suitable increased-safety terminal enclosure assemblies. View Range

Conclusion: Protect the Complete Certified Assembly

The most important principle in ATEX junction box installation is that explosion protection depends on the complete certified assembly. Correct terminals, permitted loading, compatible cable entries, reliable earthing and sound enclosure sealing all contribute to the installation’s integrity.

By checking requirements before installation, following the approved configuration and completing the appropriate inspection, engineering and maintenance teams can reduce the risk of unsuitable components or modifications affecting hazardous-area equipment.

Thorne & Derrick supply certified junction boxes and electrical enclosures to support hazardous-area electrical installations throughout the UK and internationally.

Technical note: This guide provides general engineering information. Equipment-specific certificates, manufacturer instructions, adopted standards and assessment by competent hazardous-area personnel take precedence for an actual installation.