ATEX Lighting vs Standard Industrial Lighting: What’s the Difference?

Published 02 Nov 2026

ATEX Lighting

ATEX lighting and standard industrial lighting may look similar, use the same LED technology and provide comparable illumination, but they are designed for different operating environments. The most important difference is that ATEX lighting is assessed for use in specified potentially explosive atmospheres, whereas conventional industrial lighting is not automatically suitable for these locations.

Industrial LED floodlights, high bays and linear fittings can offer excellent energy efficiency, ingress protection and durability. However, an IP66 rating, robust metal enclosure or high lumen output does not establish that a light fitting can safely operate where flammable gases, vapours or combustible dusts may be present.

For engineers, maintenance managers and electrical contractors, understanding the distinction is essential when upgrading site lighting, replacing obsolete fittings or specifying luminaires for facilities containing both hazardous and non-hazardous areas.

This guide compares ATEX LED lighting vs standard industrial LED lighting, explains the importance of explosion protection certification and identifies the factors that determine where each type of luminaire can be installed.

Thorne & Derrick supply ATEX and IECEx hazardous area lighting from leading manufacturers including Raytec, Eaton CEAG, Appleton and other specialist lighting brands.


Quick Answer: What Is the Difference Between ATEX and Industrial Lighting?

ATEX lighting is designed and assessed to operate safely within specified potentially explosive atmospheres. It incorporates explosion protection measures appropriate to its certification, such as controlling ignition-capable electrical faults, limiting surface temperatures and providing suitable enclosure protection.

Standard industrial lighting is designed for demanding environments such as factories, warehouses, workshops and industrial buildings but does not automatically incorporate the explosion protection measures or certification required for hazardous areas.

Both types of lighting may provide similar illumination, energy efficiency and environmental protection. The distinction is their suitability for use where an explosive atmosphere may occur.

ATEX Lighting vs Industrial Lighting: Quick Comparison

Primary Application ATEX lighting: certified hazardous areas. Industrial lighting: non-classified industrial environments.
Explosion Protection ATEX lighting incorporates assessed ignition protection measures. Standard industrial lighting is not automatically assessed for this purpose.
Certification ATEX lighting requires appropriate hazardous-area conformity and marking. Conventional industrial lighting does not necessarily have this certification.
IP Rating Both can provide high ingress protection. IP rating alone does not establish ATEX suitability.
Light Output Both can use efficient LED technology and provide high-quality illumination.
Selection Priority Hazardous-area suitability first, followed by illumination, environmental and installation requirements.

What Is ATEX Lighting?

ATEX lighting refers to luminaires intended for use in potentially explosive atmospheres and assessed under the relevant explosion protection requirements.

These atmospheres may contain flammable gases, vapours, mists or combustible dusts which, when mixed with air in suitable concentrations, can present an ignition hazard.

Electrical equipment can introduce potential ignition sources through electrical arcs, sparks, excessive temperatures and certain fault conditions. ATEX luminaires incorporate explosion protection measures designed to address the relevant risks for their certified use.

Where Is ATEX Lighting Required?

Certified hazardous-area lighting may be required in locations such as:

  • Oil and gas facilities – areas around suitable processing and handling equipment where explosive atmospheres may occur.
  • Petrochemical plants – classified areas associated with flammable substances.
  • Chemical manufacturing – production and storage locations with identified gas or vapour hazards.
  • Tank farms – classified locations around storage and transfer systems.
  • Pharmaceutical manufacturing – process areas where flammable solvents or combustible dusts present a risk.
  • Food processing – classified combustible dust environments where the assessment identifies an explosive atmosphere hazard.

Not every location within these facilities is classified as hazardous. The requirement for certified lighting depends on the site’s hazardous area classification and risk assessment, not simply the industry in which the equipment is installed.

Thorne & Derrick supply hazardous area LED lighting and ATEX light fittings suitable for specified gas and dust hazardous areas.


What Is Standard Industrial Lighting?

Standard industrial lighting is designed to illuminate factories, workshops, warehouses, production environments and other industrial workplaces where suitable conventional electrical equipment may be installed.

Industrial light fittings are often designed for more demanding conditions than conventional office or domestic luminaires.

Depending on the product, they may offer:

  • High lumen output for large working areas.
  • LED technology for reduced energy consumption.
  • IP-rated protection against dust and moisture.
  • Impact resistance and durable enclosure construction.
  • Corrosion-resistant materials for challenging environments.
  • Long operating life and reduced maintenance requirements.
  • Emergency lighting or integrated control options.

These characteristics can make industrial luminaires suitable for difficult operating environments, but they do not automatically provide explosion protection.

Can Industrial Lighting Be Used in a Chemical Plant?

Yes, where the installation location is not classified as a hazardous area and the luminaire is otherwise suitable for its electrical, environmental and lighting requirements.

For example, a site may contain certified ATEX lighting within a classified processing area while using conventional industrial lighting inside an appropriately assessed non-classified workshop or warehouse.

The important distinction is the classification of the individual installation location, rather than the general type of facility.


ATEX Lighting vs Standard Industrial Lighting: Key Differences

ATEX and standard industrial luminaires can share many performance characteristics. Both may use LED light sources, robust housings and optical designs suitable for demanding industrial environments.

The following differences are particularly important when specifying lighting for facilities containing potentially explosive atmospheres.

1. Explosion Protection Certification

ATEX lighting must demonstrate suitability for the intended potentially explosive atmosphere. The equipment marking and conformity documentation identify the conditions under which it can be used.

A standard industrial fitting without the appropriate hazardous-area assessment and marking cannot simply be installed in a classified zone because it appears mechanically robust.

2. Maximum Surface Temperature

Electrical equipment generates heat during operation. In potentially explosive atmospheres, hot surfaces can become a potential ignition source where temperatures exceed the relevant safe limits.

ATEX lighting must meet applicable temperature limitations for the intended gas or dust environment.

For gas atmospheres, equipment marking may include a temperature class such as T4 or T6, indicating a maximum permitted surface temperature under the specified conditions.

Conventional industrial lighting may have specified operating temperatures, but this does not necessarily establish suitability against the ignition characteristics of a hazardous atmosphere.

3. Electrical Ignition Protection

ATEX luminaires use one or more suitable explosion protection concepts according to their construction and certification.

Different concepts address ignition risks in different ways, such as preventing ignition-capable conditions, controlling electrical energy or containing an internal explosion.

A conventional industrial LED luminaire does not automatically incorporate these assessed protection measures.

4. Enclosure Design and Cable Entries

The enclosure, electrical connections, cable entry arrangements and sealing components can all affect the integrity of explosion-protected equipment.

ATEX luminaires must be installed using the entry devices, accessories and methods permitted by their certification and manufacturer instructions.

5. Maintenance and Replacement

Certified hazardous-area luminaires must be maintained so that their explosion protection characteristics remain intact.

Unauthorised modifications, unsuitable replacement components or incorrect cable glands can compromise equipment conformity.

Maintenance of conventional industrial lighting remains important for electrical safety and reliability, but hazardous-area equipment introduces additional inspection and protection requirements.

ATEX vs Industrial LED Lighting: Technical Comparison

Consideration ATEX LED Lighting Standard Industrial LED Lighting
Hazardous Area Suitability Specified through the equipment certification and marking. Not established without appropriate explosion protection conformity.
Ignition Protection Incorporates certified protection measures. Not necessarily designed or assessed for explosive atmospheres.
Temperature Limits Subject to explosion protection temperature requirements. Subject to standard product operating limits.
IP Protection Specified according to product and protection requirements. May also offer high IP ratings.
LED Efficiency Depends on the selected luminaire. Depends on the selected luminaire.
Typical Installation Appropriately classified hazardous areas. Suitable non-classified industrial areas.

Why an IP66 Light Fitting Is Not Automatically ATEX Certified

One important misconception is that a robust IP66 or IP67 industrial light fitting can be used in a hazardous area simply because its enclosure is protected against dust or water ingress.

These ratings address environmental ingress under defined test conditions. They do not establish the equipment’s protection against ignition of potentially explosive atmospheres.

What Does IP66 Actually Mean?

The IP classification system describes the degree of protection offered by an enclosure against ingress of solid objects and water.

For an IP66 fitting:

  • The first digit, 6, indicates dust-tight protection under the applicable test conditions.
  • The second digit, 6, indicates protection against powerful water jets.

An industrial luminaire can therefore be highly resistant to environmental ingress without having undergone the assessment required for use in potentially explosive atmospheres.

What About an IK Rating?

An IK rating describes mechanical impact resistance under defined test conditions.

Although impact resistance may be valuable in demanding industrial environments, it does not establish ATEX certification or suitability for a particular hazardous-area zone.

IMPORTANT: IP66, IP67 and IK-rated industrial luminaires are not automatically suitable for Zone 1, Zone 2, Zone 21 or Zone 22. Always verify the complete hazardous-area equipment marking and certification.

How Does ATEX LED Lighting Control Ignition Risks?

ATEX LED lighting incorporates explosion protection measures appropriate to the assessed design and intended hazardous atmosphere.

The use of LED technology can offer energy efficiency and reduced maintenance requirements, but LED technology alone does not make a luminaire explosion protected.

Electrical Protection

Depending on the certified design, protection measures may address potential electrical sparks, arcs, insulation failures or other ignition-capable conditions.

Temperature Control

LED luminaires produce heat in their electronic drivers, LED assemblies and associated components.

Explosion-protected products must maintain the applicable temperature limitations under their certified operating conditions.

Ambient temperature, mounting arrangements and thermal management can influence the suitability of a particular luminaire.

Enclosure and Entry Integrity

Explosion protection may depend on enclosure construction, sealing, electrical entries, protective components and permitted accessories.

Manufacturers specify installation requirements intended to preserve these characteristics throughout the equipment’s operating life.

Certified Operating Conditions

An ATEX or IECEx luminaire is not automatically suitable for every hazardous area.

Its complete marking and documentation must match the required zone, gas or dust group, temperature limits and environmental conditions.


Hazardous Area Zones: Which Lighting Is Required?

Hazardous areas are classified according to the likelihood and duration of a potentially explosive atmosphere.

Gas and vapour atmospheres use Zones 0, 1 and 2, while combustible dust atmospheres use Zones 20, 21 and 22.

The required equipment category and protection level depend on the classification and the applicable risk assessment.

Hazardous Area Zones and Equipment Selection

Zone Explosive Atmosphere Normally Required Equipment Category
Zone 0 Gas atmosphere present continuously, for long periods or frequently. Category 1G
Zone 1 Gas atmosphere likely to occur occasionally during normal operation. Category 1G or 2G
Zone 2 Gas atmosphere unlikely during normal operation and, if it occurs, normally short-lived. Category 1G, 2G or 3G
Zone 20 Combustible dust cloud present continuously, for long periods or frequently. Category 1D
Zone 21 Combustible dust cloud likely to occur occasionally during normal operation. Category 1D or 2D
Zone 22 Combustible dust cloud unlikely during normal operation and, if it occurs, normally short-lived. Category 1D, 2D or 3D

These are general equipment category relationships. Selection must also consider the relevant gas or dust group, temperature requirements, equipment certification and applicable risk assessment.

For more detailed product selection information, see Thorne & Derrick’s Zone 1 and Zone 2 ATEX lighting range.


Where Should ATEX and Standard Industrial Lighting Be Used?

Many industrial facilities contain a mixture of classified hazardous areas and locations where conventional industrial electrical equipment can be used.

This can create opportunities to specify the correct lighting for each individual area rather than treating an entire site as having identical equipment requirements.

Chemical Processing Plants

Certain process areas may require ATEX-certified lighting where flammable substances can form explosive atmospheres.

Non-classified offices, workshops or other suitable areas may use conventional industrial lighting where the environmental and electrical requirements are satisfied.

Oil and Gas Facilities

Lighting near classified process equipment, storage or transfer operations may require appropriate explosion protection.

Other locations can have different classifications and therefore different lighting requirements.

Food and Pharmaceutical Manufacturing

Combustible dusts or flammable solvents can produce hazardous atmospheres in certain manufacturing and processing locations.

Where such areas are classified, lighting selection must take account of the relevant dust or gas protection requirements.

Industrial Warehouses and Maintenance Workshops

Standard industrial LED lighting can be suitable where no hazardous-area equipment requirement applies and the product meets the necessary environmental, electrical and illumination specifications.

However, a warehouse or workshop should not automatically be assumed non-hazardous without considering the activities and substances present.

Need Lighting for Both Hazardous and Non-Hazardous Areas?

Thorne & Derrick can help customers identify appropriate ATEX-certified and industrial lighting products for their individual site requirements.

DISCUSS YOUR LIGHTING APPLICATION


Raytec SPARTAN vs WARRIOR: An Example of Hazardous and Industrial Lighting

Raytec provides a useful example of how lighting manufacturers develop products for different industrial environments.

The Raytec SPARTAN range is designed for suitably certified hazardous-area lighting applications, while Raytec WARRIOR products address industrial lighting requirements in appropriate non-hazardous environments.

Both product families use LED technology, but their equipment selection requirements are different.

Raytec SPARTAN — Hazardous Area LED Lighting

Raytec SPARTAN products include lighting solutions intended for specified hazardous-area applications, subject to the certification and marking of each product.

Applications include suitably classified processing facilities, offshore installations and other locations requiring explosion-protected lighting.

Thorne & Derrick supply Raytec SPARTAN hazardous area lighting within their wider ATEX lighting portfolio.

Raytec WARRIOR — Industrial LED Lighting

Raytec WARRIOR is an industrial lighting family intended for demanding non-classified applications.

Industrial LED lighting may offer high-performance illumination and durable construction without the specific explosion protection certification associated with hazardous-area products.

Individual models should be selected according to their actual technical specifications and installation environment.

Raytec SPARTAN vs WARRIOR: Application Comparison

Consideration Raytec SPARTAN Raytec WARRIOR
Primary Focus Hazardous-area LED lighting. Industrial LED lighting.
Explosion Protection Appropriate certified models for specified hazardous areas. Not automatically suitable for classified hazardous areas.
LED Technology Yes, depending on selected product. Yes, depending on selected product.
Typical Selection Basis Hazardous-area certification plus lighting performance. Industrial lighting and environmental requirements.

The correct choice depends on the installation location and verified product certification. Products should not be substituted solely because their lighting performance appears equivalent.


How to Choose Between ATEX and Industrial LED Lighting

The lighting selection process should begin with the installation environment, followed by the required illumination performance and product suitability.

For sites with classified hazardous areas, the following information is particularly important.

ATEX and Industrial Lighting Selection Checklist

Hazardous Area Classification Confirm whether the proposed installation location is classified and identify the relevant zone.
Certification Verify the required conformity assessment, Ex marking and equipment protection level.
Gas or Dust Group Ensure the luminaire is suitable for the relevant explosive atmosphere characteristics.
Temperature Requirements Check the permitted surface temperature and ambient operating conditions.
Illumination Assess required lux levels, distribution, glare and mounting position.
Environmental Protection Consider ingress protection, corrosion, impact, cleaning and ambient conditions.
Emergency Lighting Identify any emergency illumination requirements and the relevant equipment suitability.
Maintenance Check access, replacement parts, inspection requirements and life-cycle considerations.

Where the lighting design includes multiple working areas, professional lighting calculations can help establish the required layout, fitting selection and illumination performance.

Thorne & Derrick provide hazardous area lighting design support for customers specifying suitable lighting arrangements.


Common Mistakes When Specifying Lighting for Industrial Sites

Lighting upgrades can become more complicated when products are selected based only on wattage, appearance or purchase price.

For sites containing hazardous areas, common specification errors include:

  • Assuming IP66 means ATEX certified: Ingress protection and explosion protection address different risks.
  • Using an industrial fitting in a classified area: Product durability does not establish hazardous-area suitability.
  • Ignoring gas or dust requirements: Certified equipment must match the relevant atmosphere classification.
  • Overlooking ambient temperature: Product certification may specify permitted operating temperature limits.
  • Comparing wattage alone: Suitable lighting design also requires assessment of light distribution, mounting arrangements and task illumination.
  • Making unauthorised modifications: Changes to certified luminaires or their entries can compromise explosion protection.
  • Replacing fittings without reviewing site requirements: The replacement product must meet current applicable installation requirements and the equipment specification.

A clear specification should distinguish between hazardous-area compliance, environmental protection and lighting performance. Each needs to be assessed for the intended installation.


ATEX Lighting vs Industrial Lighting – Frequently Asked Questions

Q: What is the main difference between ATEX and industrial lighting?

A: ATEX lighting incorporates explosion protection measures and conformity assessment for specified potentially explosive atmospheres. Standard industrial lighting is designed for industrial environments but is not automatically suitable for classified hazardous areas.

Q: Can an IP66 industrial light fitting be used in Zone 2?

A: Not solely because it is IP66. The luminaire must have appropriate explosion protection conformity and marking for the intended Zone 2 application, taking account of the relevant gas group, temperature limitations and equipment requirements.

Q: Is all LED lighting explosion proof?

A: No. LED technology describes the light source, not the explosion protection characteristics. Both conventional industrial luminaires and certified ATEX luminaires can use LEDs.

Q: Do all lights in a chemical plant need ATEX certification?

A: No. Equipment requirements depend on the classification and risk assessment of each installation location. Suitable conventional industrial lighting may be used in non-classified areas.

Q: Is ATEX lighting more energy efficient than industrial LED lighting?

A: Not necessarily. Energy efficiency depends on the individual luminaire’s design, LED technology and performance characteristics. ATEX certification addresses explosion protection suitability rather than guaranteeing higher lighting efficiency.

Q: Can Zone 1 lighting be used in Zone 2?

A: Appropriately certified equipment suitable for Zone 1 may generally be used in Zone 2 where its full marking, temperature limits, environmental conditions and installation requirements are compatible. Certification and product instructions must still be checked.

Q: Does ATEX lighting also need an IP rating?

A: The enclosure must provide the environmental protection required by the product’s protection concept and installation conditions. An IP rating and explosion protection marking address different requirements and should be assessed together.

Q: What information is needed to specify ATEX LED lighting?

A: Key information includes the hazardous area zone, gas or dust group, required equipment protection level, temperature limitations, ambient conditions, illumination requirements, mounting arrangements and any emergency lighting requirements.


Conclusion: Choosing the Right Lighting for Your Industrial Environment

ATEX and standard industrial LED lighting serve different purposes. Both can provide effective and energy-efficient illumination, but the defining difference is the suitability of the equipment for potentially explosive atmospheres.

Industrial luminaires may offer excellent environmental protection and reliable illumination without being suitable for a classified hazardous area. ATEX luminaires incorporate assessed explosion protection measures and must be selected according to their complete certification and intended operating conditions.

For sites containing both hazardous and non-hazardous areas, correct lighting specification begins with understanding the individual installation environments and the applicable safety requirements.

Thorne & Derrick supply ATEX, IECEx and industrial lighting solutions, supported by technical product selection and hazardous-area lighting design expertise.

Technical note: This article provides general information about lighting selection and explosion protection. Equipment-specific certification, the site hazardous area classification, applicable legislation, manufacturer instructions and assessment by competent personnel take precedence when specifying an installation.