Marechal DN9C Star-Delta Motor Connectors – AC-22 30A 415V

motor connectors

marechal dN9C

Marechal DN9C Star-Delta motor connectors have current ratings of 30A with the ability to connect motors with two operating speeds.

Marechal DN9C motor connectors guarantee the safety of personnel throughout an operation on the load (motor load or highly inductive) and a maximum voltage of 415 V.

Marechal Dn9c Star-Delta motor connectors – Technical Specification

Rated Current (with wiring according to standard)30A
Maximum Voltage415V
Ingress Protection Lid ClosedIP55
Ingress Protection Connected PlugIP54
Impact Resistance (metal casing)IK09
Ambient Temperature-40ºC to +60ºC
Flexible Wiring (Min-Max)1mm² – 6mm²
Stranded Wiring (Min-Max)1.5mm² – 10mm²
Pre-wired auxiliary contacts (5 A)screw-type
Keying Positions2

Load Break Capability of Connector

  • Comply with IEC EN 60309-1 and IEC EN 60309-4 standards  – 30 A / 415 V
  • Load-break capability according to IEC EN 60947-3 / AC-22 : – 30 A / 415 V

 

 

Marechal DN9C Star-Delta Motor Connector – AC-22 30A 415V - 1

Marechal DN9C Plug Assembly manufactured from metal with IP55 protection and 30amp current supply is configured using associated wall mounting socket, plug, wall box, outlet, inlet and handles.

A full range of boxes, sleeves, handles, adaptors and accessories can also be supplied. Marechal’s Star-Delta range of plugs and sockets are suitable for rated currents from 30A up to 50A and maximum voltage from 415V-500V

Marechal DN9C Connectors

Marechal Part NumberMarechal DN9CMarechal DS7C3
Imax per phase30 Amp Plug50 Amp Plug
Umax415 V500 V
AC-22 switching capability 30 A / 415 V50 A / 500 V
Same Dimension asDN1DS6
Auxiliary contacts (max)23
Keying Positions (To distinguish between different power supplies & applications)25
Ambient Temperature-40 °C to +60 °C for all
Wiring (terminals)screw-type

Marechal DN9C – Socket Outlets & Inlets
UmaxPolarityMarechal Socket Outlet (Female) DN9C 30AMarechal Inlet (Male) DN9C 30A
50V6P19140601918060
50V7P19140701918070
415V5P+E19140511918051
415V6P+E19140611918061
415V7P+E19140711918071
Marechal DN9C Star-Delta Motor Connector – Install & Operation Guidelines

Marechal DN9C Star-Delta Motor Connector – Install & Operation Guidelines

Installation & Operation Guidelines

  • To ease their operation, the devices must be installed as follows :
  • Install socket-outlets with the latch at the top (Figure C1), or on the side in case of risk of accumulation of foreign material inside the cover.
  • Install appliance inlets with the catch at the top. The use of connectors with cover opening at 180° may be necessary. See figure C2.
  • When this is not possible, install appliance inlets with the catch at the bottom. See figure C3.
  • When facing downwards, IP54 appliance inlets do not protect the mating connectors against streaming water. Use IP66 devices. See figures C2/C3.

Wiring

  • Remove an adequate length of cable outer sheath according to the accessory used. Ensure that the cable sheathing extends through the cord grip into the handle or box as required to achieve the intended sealing and cord gripping performance.
  • Strip conductor insulation to the length indicated. See table T1
  • Do not back terminal screws completely out ;
  • Fully insert the conductor and tighten the terminal screws to the torque indicated. See table T1.

Mouldings display a double marking according to their use, emitting side or receiving side :

  • socket-outlet/connector terminal numbers are preceded by an “S”;
  • plug/inlet terminal numbers are preceded by an “F”.

E.g. F4/S2 : This terminal receives conductor n° 4, plug side and conductor n° 2, socket-outlet side.

  • DN9C socket-outlet/connector : see figure F2,
  • DN9C plug/inlet : see figure F3,

Tension Cord

The release of the latch is performed by a tension cord. One end of this cord must be attached either to the flexible cable or to a suitable fixed point of the installation. The other end is attached to the latch release mechanism.

Latch Release Mechanism

This mechanism comes in two different types :

  • Ejecting connector : The retaining latch is directly activated by the tension cord in case of traction. See figure E1.
  • Ejecting plug : A mechanism is assembled on the plug. It releases the retaining latch of the socket-outlet in case of traction on the tension cord. See figure E2.

For the larger plugs, a cam mechanism inserted between the plug top and the handle. See figure E3.

Eyelet

Some handles are equipped with an eyelet. This eyelet allows an optimal pulling angle of the tension cord on the latch release mechanism. See figures E1/E2.

Assembly

The end of the tension cord that must be attached either to the flexible cable or to a suitable fixed point of the installation is equipped with a loop. A crimping ferrule is supplied to loop the other end of the cord, once it has been passed through the handle eyelet, the latch release mechanism, and cut to the adequate length.

Cable Tie

A cable tie is supplied, to attach the loop of the tension cord onto the flexible cable.

Sealing Rings

Insert a sealing ring between the device and its rear accessory (handle, angle, etc.). The two protrusions of the rings must be positioned on the latch side for the socket-outlet/ connector and on the catch side for the plug/appliance inlet.

Operation

  • The socket-outlet is shielded by a protective lid held in the closed position by a latch.
  • Depress the latch to release the lid. See figure F5.
  • To connect, align the bayonets of the device with the hollow parts of the complementary device. Insert the device and turn until the stop. The device is in the rest position, circuit open.
  • Push the device fully home until latched.
  • To disconnect, depress the latch. The device returns to its rest position.
  • Turn the device clockwise to remove it. Shut the lid.

Self-Ejecting Devices (Marechal DN Only)

  1. Lift the latch to release and open the lid.
  2. Align the plug/inlet catch with the socket-outlet retaining latch and push the mobile part fully home until it is held in place by the latch.
  3. To release the mobile part, pull on the tension cord. Check that the cover is properly closed.
Power Distribution & Control In Hazardous Areas

T&D also distribute hazardous area isolators, control panels and distribution boards, electrical enclosures and motor starters certified according to ATEX for use in Zone 1 & Zone 2 (gas/vapour) explosive atmospheres.

Hazardous Area ATEX Zone 1 Zone 2 - Power Distribution

Data Sheets